2 channel analog input module with 1-wire interface

Voltage measurement: 0-60V

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

2 channel current transmitter with 1-wire interface

current measurement: 0-20mA (4-20mA) current loop

Select voltage measurement: 0-10V with Mode to GND

Resolution: 16bit

Accuracy: +/-1%

Input is galvanically isolated

Supply voltage: 5VDC 25mA

Temperature range: -20 - +60°C

IP20

Dimensions: 120 x 36 x 60 mm

DIN mounting

AC and DC voltage meter with true RMS
Resolution: 24 bits
0-264VAC 0-60Hz (3 phases)
L1, L2, L3, N
0-+/-370VDC
Input impedance greater than 2.4Mohm
Modbus RTU (2-wire RS485)
Built-in RS485 termination (120 ohms)
Up to 63 units per RS485 Bus
LED for communication status
Response time: less than 50mS
Temperature: -20 - +60°C
Supply voltage: 5 - 28VDC
Dimensions: 86 x 59 x 35 mm

1-wire communications - several sensors can be connected to the same unit
± 3.0% relative humidity accuracy
± 0.4% relative temperature accuracy
12 bit resolution for humidity measurement
14 bit resolution for temperature measurement
Calibrated digital output
Eksellent long-term stability
Each sensor has its own unique 64-bit serial number

1-wire Temperature / Humidity sensor
Temperature -20 - +60°C
Humidity 10 - 90% RH
Temp tolerance +/-0.4°C at -10 - +60°C
Moisture tolerance ±3.0%rH at 20 - 80%rH
Long term operation ±0.25%/year at 20 to 80%rH
Long-term operation ±0.05°C/year at -10 to +60°C
Solution 0.1 %rH 0.1 °C
Power supply/consumption 4.0 to 5.5 VDC 5 mA
Dimensions 62 x 28 x 16 mm
Cable length 1 m

Temperature and humidity sensor
1-wire interface for Teracom controller
Temperature: +/-0.4 °C (-10 to +60 °C), max. +/-0.6°C
Resolution: 0.1°C
Humidity: +/-3.0% RH (20 - 80% RH), max. +/-5% relative humidity
Solution: 0.1% RH
Supply voltage: 4.5 - 26VDC
LED indicator for communication status
Long-term stability based on digital signal processing
Changeable bit rate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Multi sensor for CO2, Temperature and Humidity
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Temperature and Humidity sensor
RS485 MODBUS RTU
Temperature: +/-0,4 °C (-10 to +60°C), max. +/-0,6°C
Resolution: 0,1°C 
Humidity: +/-3,0% RH (20 - 80% RH), max. +/-5% RH
Resolution: 0,1% RH
Supply voltage: 4,5 - 26VDC
LED indicator for status of communication
Long-term stability based on digital signal processing
RS-485 interface (2-wire) carrying up to 32 nodes
Changeable bitrate and other communication parameters
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g

Multi sensor for CO2 and Barometric pressure
Interface: RS485 - MODBUS RTU
LED indicator for status of communication
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Changeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4,5 - 26VDC / Max. 150mA

Multisensor for CO2 and barometric pressure
Interface: 1-wire (+/- and data)
LED indicator for communication status
Long-term stability based on digital signal processing
Self-calibration on fresh air for CO2 measurements
Interchangeable communication parameters
Non-volatile memory for all settings
Firmware update via the interface
Size: 81 x 81 x 30 mm
Weight: 66g
Supply voltage: 4.5 - 26VDC / Max. 150mA

1-wire Combi Sensor
Temperature: -20 - +60 ° C +/- 0.6 ° C
Resolution: 0.1 ° C
Humidity (Moisture): 5 -95% Rh +/- 5%
Resolution 0.1%Rh
IP54 Plastic housing, very sturdy
Up to 8 sensors on the same 1-wire
16 bits at temperature
12 bits at moisture
Supply Voltage: 4.5 / 25mW
Dimensions: 74 x 66 x 36 mm

RS485 Modbus RTU combi sensor

Temperature: -20 - +60°C +/-0.6°C

Resolution: 0.1°C

Humidity: 5 - 95% rH +/- 5%

Resolution 0.1%rH

IP54 plastic housing, very robust

Up to 32 sensors on the same RS485 bus

16 bits at temperature

12bit when wet

Supply voltage: 4.5 - 26VDC / 25mW

Dimensions: 74 x 66 x 36 mm

Smoke alarm with a diameter of 15 meters
installation up to 11 meters high
With potential-free relay contact
Smoke sensitivity: EN 54-7:2000+ A1:2002
Operating temperature: -10 to +55 °C
Dimensions: Ø100 mm, h 47 mm
Weight: 100 g

1-wire lysmåler til synligt lys
0 - 83.000lux med 1 lux opløsning
Op til 23bit opløsning
Automatisk fuld skala justering
Kan kaskadekoples via RJ11 stik
Forsynes fra Controller med 5VDC/4mA
Maks. 30 meter kabel
Mål: 85 x 35 x 24 mm
IP30 plasthus med flange

1-wire barometrisk trykmåler, 2 x RJ11 til daisy chain
Relativ præcision på 0.12hPa
Høj elektromagnetisk (EMC) immunitet
Høj linearitet og nøjagtighed
Nem installation
Eksellent langtids stabilitet
Hver enhed har egen unik 64 bit serienummer

Combi sensor for temperature and humidity measurement

Modbus RTU

2 x RJ45 connectors - with daisy chain to next module

RS485 Bus to Controller.

Up to 32 devices can be connected to the Controller

3.0% relative humidity measurement accuracy

12 bit resolution for moisture measurement

14 bit resolution for temperature measurement

With mounting flanges

Excellent long-term stability

Each module has its own ID code

0-20mA 4-20mA Transmitter for 1-wire output

2 x RJ11 for daisy chaining

10-bit resolution

0-20mA and 4-20mA, 0.01mA resolution (+/-2%)

Galvanic isolation

IP30 tight

Good long-term stability

Each device has a unique 64 bit serial number

Temperature sensor with Dallas chip - up to 8 pieces on the same bus
1-wire communication to the measuring electronics
± 0.5 ° C accuracy from -10 ° C to + 85 ° C
12 bit resolution
Aluminum head provides low thermal resistance
IP65 close
Very low power consumption
Each unit has a unique 64 bit serial number

1-wire communication - 2 x RJ11 connectors for daisy chain connection
2 - 3 - 4 wire Pt100 temperature sensor - 4 wire is recommended.
Built-in A/D converter with compensation
24 bit resolution for temperature measurement
Calibrated digital output
Excellent long-term stability
Each sensor has its own unique 64 bit serial number

Remote data collection, remote meter monitoring, energy management

Energy meter interface module with MODBUS RTU

RS-485 interface with up to 63 devices per BUS

Built-in 120 ohm termination resistor

Flash memory for data and setup

Voltage supply from 5 to 30VDC, 50mA at 5VDC

Galvanically isolated digital inputs - 10mS polling rate

Optional inputs: Open/Closed (dry contact and 32 bit counter)

S0 pulse counter applications:

Remote monitoring of electricity meters

Industrial process control

Remote monitoring of gas meters and water meters

Monitoring of devices with S0 outputs;

Process monitoring

DIN rail mounting

Firmware update via interface.

Dimensions: 35 x 86 x 59 mm