MOXA ioLogik E2210
Ethernet Micro RTU Controller
1 x 10/100 Mbps, RJ45
1.5 KV magnetic isolation
Modbus / TCP, TCP / IP, UDP, DHCP, Bootp, SNMP ( MIB for I / O and Network), HTTP, CGI, SNTP
RS-485-2w Data +, Data-, GND
15 KV ESD
12 x digital input - source type
Digital output: 0 to GND
Logic 1 open
Wet Contact: Logic 0 0:02 3 VDC
Logic 1 10:02 30 VDC (DI COM two DI)
8 x Open Collector sink type: 36 VDC / 200 mA 
Power supply: 12-36 VDC

8 channel analog output module, Modbus protocol
Source type power output
8 x 12-bit analog outputs
Individual Channel Configuration
Cable Break Detection at 4-20mA
8kV ESD Protection
Power-on Value Programming
Security Value Programming
Temperature -25 to +75°C

Gateway from Ethernet slave to PROFIBUS master
protocol / hierarchy: DP-V0 Slave
PROFIBUS Speed ​​(Kbps) in 10 step from 9.6 - 12000
speed setting is automatic
Max. Input data length: 240 byte
Max. Output data length: 240 bytes
Address setting: 0 ~ 126 Set by DIP switch or EEPROM
Ethernet protocol: TCP / UDP server / client
Configuration: Web Configuration

ANALOGT INPUT MODUL TIL MODBUS

HMI control with 4.3 "TFT Touch
IP40
interface: 2 x RS485
USB port for download
RTC - Real Time Clock
Free HmiWorks Development software
Supply voltage: 12 - 48VDC
Temperature: -30 - + 50 ° C
Goal: 140 x 87 x 41 mm
Less-Surface-Exposed Housing Design Design

Ethernet module with 2 digital inputs and 1 relay output
2 x digital dry contact - active high by connecting contact
1 x Power relay, 250vac / 5a, 30vdc / 5a
Avoid inductive load to relay
P2P Function that reflects an input to other module output
Supports Modbus / TCP and UDP Slave
Power supplied from PoE or 12 - 48VDC
PoE: IEEE802.3af, Class 1
Operating temperature: - 25 - + 75 ° C
Dim: 98 x 52 x 27 mm
DIN bracket

5 kanals analog input
2 kanals analog output
2 kanals digital input
2 kanals digital output

Pt100 sensor with 2 m cable
Steel tip of 100 mm ø3.2
Cable is rated for -80 - +200°C

RS485 module with 2-channel strain gauge gauge
high resolution: 16-bit
excitation voltage range: 0 ~ +10 V.
50 Hz Event counter (digital input)
high / low alarm (Digital Output)
Linear Map Function
3000 VDC Intra Module Isolation
Double Watchdog
Temperature Area: -25 to + 75 ° C
Supply Voltage: 10 - 30vdc
Dim: 123 x 76 x 35 mm

125 Ω Shunt resistance, 1 pc. pr. Channel

RS485 module with 3-axpet Encoder input
1MHz Frequency input
input voltage: Up to 5VDC
Other voltages are with external resistance
32 bit counter
Quadrant, Pulse / Dir, CW and CCW
RS485 port - 1200 - 115.2K Baud
Supply voltage: 10 - 30VDC
Dim: 123 x 72 x 35 mm

RS485 Frequency counter with 2 digital outputs
2 x counter entrance Max. 100kHz
input is Wet / Sink - Max + 30volt
32 bit counter - count up
for frequency and pulses
2 X Digital Output - Open Collector (OC)
Max. OC voltage: 30VDC / 30MA
Supply voltage: 10 - 30VDC
Dim: 123 x 72 x 35 mm
Operating temperature: -25 - + 75 ° C

HMI Panel with LCD Display, Ethernet and Com Ports
Can be connected to most of the manufacturer's I / O modules
Power supplied from PoE or 12 - 48VDC / 2.5 Watt
RS-485 (with self-tunes) < Br> RS-232 (RX / TX / GND)
RTC - Real-time tour
GUI design
Free HmiWorks development tools
supports C and Ladder designer
design suggestions from manufacturer
Modbus TCP / RTU protocol
Dim: 140 x 87 x 41 mm

Accessories
Protective cover
for DIO-RXX and DIO-TXX

50 cm DIN skinne model TS-35, med en højde på 7,5 mm

37-polet terminalkort 
16 stk. BNC 3
37 banan 4mm stik

2.4GHz Omni directional antenna - dipole
for pipe montage
N-female connector
1 meter RG58 Coax cable
1 pc. RSMA - Male included
Weight: 1.4KG
Length: 45 cm
Diameter: 35mm

5,0 meter kabel til brug mellem I/O-kort og TERM100S

3,0 meter kabel til brug mellem I/O-kort og TERM100S

1 meter kabel til brug mellem I/O-kort og TERM100S